Nothing could be easier to accomplish than these rustic, personalized wood slice tree ornaments. After slicing a log into discs, screw in an eye hook, and thread with some jute twine for a hanger. Decorate with paint or metallic markers, or try the clever ink-jet-printer transfer technique that Upcycled Treasures used for the ornaments shown here. One log will make gifts for your entire extended family.
Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools. Next to the radial arm saw and in the corner is the floor drill press with accessory storage next to it for all drilling operations.  Across from the radial arm saw is a separate workstation set up with a small portable table saw and router set-up with storage underneath for routers, bits and accessories.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
In regards to flattening the top, another technique would be take a pencil (soft lead) and lightly draw some big lazy squiggles across the top - enough so that there is a line every few inches. Then, use either a jointer plane or a belt sander to flatten the top until the squiggles are gone. The lines give you a reference to what is high and what is low - and when you are finished in a particular area. With the jointer plane, you want to stroke at about 45 degrees to the grain of the wood, and with a belt sander, you want to keep the sander flat on it's platen (don't let it tilt and dig in) and use wide, arcing, sideways sweeps with very light pressure - again at about 45 degrees to the grain of the wood - never let the sander start or stop when in contact with the surface. In both cases, finish with light sanding with either a belt sander, linear sander, or by hand, stroking in the direction of the grain. Palm sanders can leave swirls. 

As you can see in the image, this beautiful heart shaped wall hanging wooden piece on the wall. It looks beautiful and can be used to surprise someone special. The shape and design of this wooden hanging depend on how properly you build it. First time workers definitely need some guidance to help them with the process. You can choose the wood type, color and design as you like for your project. You can easily make it at home by using some artthings. You can decorate your wall hangings with different materials, designs and styles. I am actually making one of this wooden heart shaped hanging in my home. It is perfectly cool and artistic work. These hangings may be adjustable or a fixed.
In the parties you always need a candle stand for enhancing your decoration. This candle stand is a very stylish one and it always adds beauty to your lounge. In the washroom, you also need some candles while having a bath. In the washroom, you can keep this candle stand on one side. The soothing effect would increase by these candles and this candle stand is really a marvelous one as it is made in a stylish way. You can create it very easily and can give it to your friend as a gift. Let’s have a look at the pictures which I am sharing with you.

#00 Steel Wool and White Vinegar – Put a handful of steel wool in a jar and add white vinegar. Let the vinegar dilute the steel wool for at least a couple days. The mixture will get darker the longer you let it sit. Once diluted, simply paint the mixture on your piece. Oxidation will occur and the mixture reacts with the tannins in the wood to give it variations in color. It changed the Fir wood to dark blues, greys, browns, and black. Do not use white Pine because it will not darken much at all.


Woodworking project plans provide extensive assistance. Project plans are available with variations of Santa and his sleigh and reindeer, candy canes, polar bears, trains, and toy soldiers. Or maybe you’d prefer a more religious display. Wouldn’t an angel or a nativity scene look heavenly on your front lawn? You’ll be able to find project help for practically anything you think of related Christmas.
Your earliest notes on woodworking will look much like notes from your first days at a new job: they're comprised of words you've heard, the lingo of a community and those in the know, that don't make any sense. Just as, at a new job, you will write a word like "Aditi?" and learn that it's a nickname that means "development server," so your first notes will be "biscuit joint?" and "joiner planer? planer joiner?"
Methods for skinning a cat have nothing on ways to build a bench. Explore different joinery methods and work with those that you are able to complete the best. Don't overcomplicate something when it doesn't need to be. There's a reason tools have improved, glue has gotten better, fasteners stronger, and new joinery methods have been introduced. A lot of the time the focus in woodworking is on finding shortcuts to get the same or better results. Don't let joinery snobs influence you. 

This wooden sofa side table can also be made in different sizes and shapes as you can find on the internet. Some of the items you will need for this project are wooden pieces, cutter, screws, etc. We have included a video tutorial here that illustrates the process of building a wooden sofa side table. This is not the exact one that you see in the image above, but it can be modified to build any shape or design you want. The video tutorial also has English subtitles to make it easy for anyone to understand and follow the steps.
In this month’s woodworking project demonstration, George Vondriska teaches you the step-by-step process for building a coat tree that will look great in your home or workshop. He demonstrates the simple techniques for installing wrought-iron hooks, crafting the coat tree’s feet, and quarter sawing to achieve that beautiful face grain on all four sides.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
All content on this blog is the property of Just the Woods, LLC. You are welcome to share my content (to include one photo only) as long as you provide a link back the original post. DO NOT copy entire posts, or crop, edit, or remove watermarks from photos without written permission from me first. Sharing a post from Just the Woods in a capacity where YOU will be compensated is not permitted. Thank you!
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.

All content on this blog is the property of Just the Woods, LLC. You are welcome to share my content (to include one photo only) as long as you provide a link back the original post. DO NOT copy entire posts, or crop, edit, or remove watermarks from photos without written permission from me first. Sharing a post from Just the Woods in a capacity where YOU will be compensated is not permitted. Thank you!


Liz Fourez started Love Grows Wild in 2012 with a passion for interior design and homemaking and a dream to help others create a home they love.  From simple project tutorials, to holiday and entertaining ideas, to her journey renovating a 1940’s farmhouse, Liz demonstrates how to create a beautiful and inviting home with a handmade touch. She turned her signature cozy, neutral style into a best-selling book in 2016 and continues to inspire readers with her captivating photography and easy decorating ideas. Read more about Liz > > > >
After cutting the rabbet joints, we walk you through the glue-up and assembly of the box. This critical stage in the process involves applying glue to the box parts and using clamps to hold the parts together while the glue dries. The assembly and glue-up tips that we detail in this episode -- and our companion article -- can apply to the assembly of any woodworking project.
Farm tables are those warm, rustic surfaces that draw inspiration from the original harvest tables found in American homes of the 18th and 19th centuries. Rather than being built by skilled and trained artisans, farm tables were assembled from large and rough planks of fir. Their construction valued sturdiness and utility over detail and refinery. Today, farm tables can bring a sense of antique charm to any home, complementing matched chairs and contemporary benches alike. Here are five DIY farmhouse table projects to inspire your next act of handyman prowess.

Scrollsaws are good for projects like cutting puzzles or silhouettes of cutesey animals out of wood. But for making furniture, scrollsaws just aren't up to the task. Scrollsaws, along with Dremel tools, do have their uses in crafts, but for woodworking, they are just a little too small. That said, Dremel tools are very useful for sharpening brad point drill bits, forstner bits, and bandsaw blades, so they do have a use in woodworking.
Methods for skinning a cat have nothing on ways to build a bench. Explore different joinery methods and work with those that you are able to complete the best. Don't overcomplicate something when it doesn't need to be. There's a reason tools have improved, glue has gotten better, fasteners stronger, and new joinery methods have been introduced. A lot of the time the focus in woodworking is on finding shortcuts to get the same or better results. Don't let joinery snobs influence you.
Table saws, band saws, and radial-arm saws are examples of woodworking machines that are most often used exclusively in a wood shop because they are far too large and cumbersome to be portable. Even though they're confined to the shop, these workhorses are so useful that it makes sense to complete a woodworking project in the shop and carry the finished piece to the location or job site where it will be used or installed. 

Here is a look at the completed table prior to staining and sealing the piece. I also created matching benches to fit this table. The plans can be found by clicking here. I modified the width so they are a total of 69″ wide. Instead of using a 2×10 for the breadboards I use 2×8’s. Everything else was kept the same as Ana’s plans. The inside span of my table where the benches fit in is 73″ so that left 2 inches of wiggle room on each side of the bench so it can easily slide in and out.
But first, this build was sponsored by Timber Wolf Forest Products.  They provided the legs for the build.  Also, HomeRight provided the paint sprayer for this project.  All opinions are my own and are uninfluenced.  This post also contains affiliate links.  See disclosure policy for details.  If you purchase from these links, I may receive a small commission at no extra cost to you.  This helps keep the content on this site free.  Thank you for your support and for supporting the brands that help support this site.

I can't really make good recommendations as to what specific brands of tools are better than others. Most of my tools were opportunistic purchases, with relatively little regard to specific brands. More often than not, it's price and a quick inspection to gauge the solidity of the tool that are the determining factors. My tools are usually not among the best that can be had, but good enough.

Hardwood boards and softwoods may look similar in shape and dimension, but they are sold using completely different measuring systems. Softwoods are typically sold in standard lumber dimensions (such as a 2x4), whereas hardwoods are most often sold by the board foot. Calculating board feet helps you guarantee that you're getting your money's worth on every piece of hardwood you purchase.


The Saw Guy - Saw Reviews and DIY Projects Copyright © 2018. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here 

Never consider using wood from a high volume store such as Lowes or Home Depot for furniture. You will almost assuredly have serious warpage as this wood is never dried to the proper level prior to being placed in the stores for sale. I normally shoot for 7%-8% moisture content. Anything greater than that will have a tendency to warp as it continues to dry out. You need to go to a lumber yard where the boards are actually dried prior to sale. You can acquire an inexpensive meter and check the boards yourself prior to purchase. Actually, I prefer air dried lumber as opposed to kiln dried. I have let it dry for 1-2 years or more prior to using it. I don't run it through the planer until I am ready to use it. Hope this is helpful. By the way, Red Oak or Cherry makes beautiful furniture. I seldom use white oak because the stuff is really tough to work with due to its hardness. Make beautiful furniture, though!

Because these legs were salvaged they had old screw holes in them which were filled prior to painting.  In retrospect, it probably would have looked cool to just leave them.  I lightly sanded the legs with 100 & 150 grit sandpaper which smoothed them without removing all the saw marks.  One coat of chalk paint and 2 coats of clear Briwax was used to finish the legs.  Briwax yellows the finish a bit which aged the paint nicely.  Between coats of Briwax I sanded through the paint on some of the edges with 100 grit paper to show wear.  
Have you ever tried the projects that are unique and have some more modern looks? If you haven’t, I will show you some of the new and modern looking ideas which would surely admire you. Try these at your home and add the rare and unique items in your decoration. Here I am sharing 23 wood items with you and I hope you would enjoy the list. So, these modern look projects would give you a good start of making the modern woodworking items. Have a look at these woodworking ideas to get the amazing ideas.
In my project section I wrote an article about small boxes made with a router. The article was written years ago and the boxes were made several years before that. Thus, I had to use one of those old boxes to write this article as I couldn't exactly remember how I made them. The initial construction process came from that great Canadian TV show, The Router Workshop, but the jig I use was born of necessity. One year I decided to build a pile of these boxes and enter a craft fair. After two or three, I decided there had to be a faster way to set up for the cuts, so I used a discarded table saw sled to fashion the jig in this article.
Easygoing style Kitchen Farm Table Cultivate tables, otherwise called reap tables, once utilized as durable work surfaces for agriculturists. Today, their straightforward wooden plan settles on them magnificent decisions for the lounge area and kitchen. In the principal room, a provincial ranch table replaces a focal island in the kitchen, giving a spot to easygoing suppers.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
Nothing could be easier to accomplish than these rustic, personalized wood slice tree ornaments. After slicing a log into discs, screw in an eye hook, and thread with some jute twine for a hanger. Decorate with paint or metallic markers, or try the clever ink-jet-printer transfer technique that Upcycled Treasures used for the ornaments shown here. One log will make gifts for your entire extended family.
*Please NOTE: While my table has held up well and had only a small amount of movement after 2 1/2 years, there are certainly things I would do differently with more experience under my belt. For beginners, I'd recommend using biscuits and glue for the top planks. Dowels or floating tenons/dominos are another option. Do make sure to let the wood properly dry.

There’s no denying the value of a handmade gift. There’s still time to make a project and have it ready to give as a gift this holiday season. Here are fifteen woodworking projects that would make great holiday gifts for a wide range of people. Most are not difficult and some can be completed in a day. You can probably build a few of them with scraps you have around your shop. Just click on the project name to go to the full project article.


Hand Tool Storage Cabinet and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Ridgid Drill/Impact combo, Bosch multipurpose drill bits … [Read more...]
This saw has changed my life. I literally cannot even tell you who I am anymore. I have been reborn, and into a world where the lion lays with the sheep in euphoric happiness and cooperation. The skies are bluer now than ever before. My tastebuds have been supercharged; my skin feels tingly all through the day; my mind has been freed and I have new purpose and resolve.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
A good friend celebrated a milestone birthday this year, and since he’s a real wine afficionado, I wanted to give him a few very nice bottles of wine presented in a special way. I’ve seen expensive vintage wines sold in wooden presentation boxes, but I wanted to make something that’s well beyond the ordinary. So I designed a box that presents the wine bottles by “popping them up” as the lid is opened.
×