If you like a large octagon table instead of a simple round table, you can consider this free DIY plan from Ana White. This table features truss supports and pedestal base which makes it extremely durable and stable. The look might unnerve you because of the angle cuts, but you can easily get this task accomplished with the right tools. The entire list of the tools and materials required are provided. Also, the instructions are very easy to follow with illustrations included. The table has the capacity for seating six people, and it can be manufactured with a budget of around $110.
Here is a look at the completed table prior to staining and sealing the piece. I also created matching benches to fit this table. The plans can be found by clicking here. I modified the width so they are a total of 69″ wide. Instead of using a 2×10 for the breadboards I use 2×8's. Everything else was kept the same as Ana's plans. The inside span of my table where the benches fit in is 73″ so that left 2 inches of wiggle room on each side of the bench so it can easily slide in and out.

Work with attention and don’t forget that a good planning will save you from many issues and it will keep the costs within your budget. Invest in high quality materials, such as pine, redwood or cedar. Drill pocket holes before inserting the galvanized screws, to prevent the wood from splitting. Add waterproof glue to the joints, in order to enhance the rigidity of the structure.

Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
Hand Tool Storage Cabinet and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Ridgid Drill/Impact combo, Bosch multipurpose drill bits … [Read more...]
So many ideas are included in this website, just waiting for you to build memories with inexpensive wood projects. You will find a variety including outdoor projects, furniture plans, household accessories, craft fair items and workshop furnishings.  There is also a host of projects suitable for a beginner. Build one of these great projects this weekend!
Use: White vinegar poured into a glass jar with steel wool that you have pulled apart and loosened. After fifteen minutes, brush onto the wood. After the surface is dry, you can leave it as-is or clear coat it with a product like Minwax One Coat Polyurethane. Distress prior to finishing, if so desired.http://www.wikihow.com/Age-Wood-With-Vinegar-and-Steel-Wool 

Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block. 

Don't believe the mainstream thinking that hand tools are irrelevant, too slow to be useful, or less effective than power tools. Ignore, or at least take with a grain of salt, the power tool devotees who will say "There's a reason they invented power tools, ya know!" Your "shop" is a bench attached to the inside of a coat-closet door in a one-room studio apartment right now. Power tools are going to bother that nice med student next door, and that closet shop doesn't have any ventilation for the amount of dust you'll produce. Hand tools can be more efficient (in speed, quick access, storage, and lack of set up), they're quieter, and the pleasure of silence afforded by quiet hand tools--just a few soft noises produced by your tools--is a pleasure not to be overlooked. They're portable and will move with you, you'll learn more about how different types of wood behave, and, when you run into one of those power tool zealots, just go over to Todd's house and watch a few episodes of The Woodwright's Shop to get your respect for hand tools back in check.

Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.


This cute earring box is the ideal one for giving the gifts to your loved ones. Have you ever given your gift in a wooden jewelry box? When you meet with your friends and family it is a very great idea to surprise them with such gifts. They would really admire your selection. I am sharing some of the pictures with you, which are about this earring box. Have a look at these pictures; I am sure you would like them. 

Woodworking project plans provide extensive assistance. Project plans are available with variations of Santa and his sleigh and reindeer, candy canes, polar bears, trains, and toy soldiers. Or maybe you’d prefer a more religious display. Wouldn’t an angel or a nativity scene look heavenly on your front lawn? You’ll be able to find project help for practically anything you think of related Christmas.
Hand Tool Storage Cabinet and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Ridgid Drill/Impact combo, Bosch multipurpose drill bits … [Read more...]
Here’s a rundown of the 5 most important beginner woodworking skills to help you get started. When you’re done, have a go at our custom sit-stand desk DIY Sitting / Standing Desk DIY Sitting / Standing Desk Read More . For other MakeUseOf DIY projects, you’ll probably need some electronics skills Beginner's Electronics: 10 Skills You Need to Know Beginner's Electronics: 10 Skills You Need to Know Many of us have never even touched a soldering iron - but making things can incredibly rewarding. Here's ten of the most basic DIY electronics skills to help you get started. Read More , too.
I think this is one of the best feelings if you are successful in making wooden spoon by yourself without any trouble. You can create stylish and unique spoon at home. The only thing is that you just need to follow some steps for making a perfect spoon. In this video, you can see how simply the making of a spoon is and how much you need time for making is explained in this video.
Creating custom picture frames for friends and family is a great gift giving project that's sure to please even those difficult to shop for gift recipients. Everyone has a special photo or keepsake they've meant to have framed. Making a custom frame to match may be the best gift of the season. Best of all, it's a quick and simple project to complete with the right tools and set up.

These attractive gifts look like mini treasure chests. Here are the free woodworking plans, and assembly instructions to make these nice looking wooden boxes (Children's Mini Desktop Treasure Chest) from scratch. Recycle that scrap wood into a fantastic gift. A rewarding Saturday Arts and Crafts project. Free DIY (do-it-yourself, D.I.Y.) to give as a gift. Make a keepsake by using these woodworking plans.
This Farmhouse Side Table post is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. Building a new farmhouse side table to go along with my farmhouse coffee table has been on my list for a … [Read more...]
All of our tables are available in the color and finish of your choice.  Our existing color pallet includes 90 paint colors,  multiple stain color options in each workshop collection and several wax color options for our reclaimed woods.  Please feel free to explore all of our paint and stain options to help guide your design plans.  All of paint and stain finishes include a durable water based clear top coat.  This makes it easier to keep the table top clean with a damp sponge (no chemicals!) and provides protection from water rings. (How to Clean a Wooden Dining Table) 
To inset the aprons 3/4" from the outer surface of the legs I made a spacer from 2 pieces of plywood.  This little jig made it easy to keep the distances uniform and also secure the apron to the leg while fastening.  Pic 3 illustrates how the jig, apron and leg are clamped together for fastening.  Each apron end is held by three 2 1/2" pocket screws.  The pocket holes were made using a Kreg pocket hole jig.  I assembled the short ends first and then the rest of the table base making sure the kerf (for clips) was along the top edge.  Since this is a long table I also added a cross piece in the middle of the table using pocket screws.
Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.

Sand the table smooth. Start with 80-grit sandpaper, and move to a finer grit for each pass. You should end with 220-grit. I finished the table with two coats of Jacobean-tinted polyurethane, then buffed on a couple of coats of wax after it was dry. The dark tint hides any scratches or nicks and also makes it look like it was built a century ago. On that note, you can give up your coasters—a little wear will only make your table look better.


A 1914 book which treats, in a most practical and fascinating manner all subjects pertaining to the "King of Trades"; showing the care and use of tools; drawing; designing; and the laying out of work. The principles involved in the building of various kinds of structures, and the rudiments of architecture. It contains over two hundred and fifty illustrations made especially for this work, and includes also a complete glossary of the technical terms used in the art. The most comprehensive volume on this subject ever published for boys.
Because the legs I used are rather large and chunky, I wanted my apron to be larger than normal so it looked proportional.  Typically, a 2×4 is fine for an apron, but I used 2x6s and cut them down to 4 1/2″ wide using a table saw.  A standard 2×6 is 5 1/2″ wide.  You could leave it at 5 1/2″, just keep in mind the chair height and make sure you will have enough leg room to slide under.  If you wanted a less chunky leg, Timber Wolf has many other options on their website 🙂
Some friends of ours have been wanting a DIY farmhouse table for some time now. After hearing about their shopping trip and the prices they were looking at spending on one I felt obligated to step in and make this one of my next DIY projects. My buddy Jake has no experience with power tools whatsoever, bless his heart. So, you’re in for a special treat with this one as you will get to see Jake build this table from scratch with no power tool experience! With a little guidance from me of course.
Summertime means loads of fun playing games outside with family and friends. We love to bring out yard games like Kubb, Croquet, and Danish Ball. My kids love to play the traditional Jenga. I thought it would be fun to make a giant sized version for the yard. The traditional Jenga pieces are 1.5 cm thick, 2.5 cm wide and 7.5 cm long, making the Giant Jenga pieces couldn't be … [Read more...]
This wooden sofa side table can also be made in different sizes and shapes as you can find on the internet. Some of the items you will need for this project are wooden pieces, cutter, screws, etc. We have included a video tutorial here that illustrates the process of building a wooden sofa side table. This is not the exact one that you see in the image above, but it can be modified to build any shape or design you want. The video tutorial also has English subtitles to make it easy for anyone to understand and follow the steps.
This project requires a fair amount of turning experience. If you’re patient, however, you’ll find that making this ornament is a good way to learn new techniques. Shaping a delicate spindles takes practice, but you can make up the shape of the icicle as you go. If you’ve never hollowed a vessel before, this ball is an easy first project—the inside doesn’t have to be smooth and polished. The ball is hollow to reduce its weight.
Copyright 2018, Sarah Pawlak. Feel free to share what you see here but please only share one image with a link back to my page. It is not permissible to copy anything else on my site without first getting written permission from me. All printables are for personal use only. Sponsored posts always include my own thoughts and are never written by the sponsors. Affiliate links may be used at times. Pinning is always appreciated!! Thank you!
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
I used a #00 Steel Wool and White Vinegar solution to patina the wood and give it an aged look. Put a good handful of steel wool in a jar and add white vinegar. Let the vinegar dilute the steel wool for at least 3 to 4 days. The mixture will get darker the longer you let it sit. I let mine sit for a full week. Once diluted, simply brush the mixture on your piece. Oxidation will occur as the mixture reacts with the tannins in the wood to give it variations in color.
Hey, I want to build all of these (and I did read to the end), but my list of projects is so long that any one of these will have to wait ’til next year (and i don’t mean January). thanks for all these ideas. there is one more i read about in the Handy Family Man. It is an adaptation to your shop vac that puts the hose at your project so it sucks up the dust as it is produced. Wonderful, right? Maybe next year!
A nice thing about a bandsaw is that it's not scary to use. Sure, a bandsaw can cut your fingers off too, but it will probably cut your finger slow enough that you can pull it back before it's a major injury. I cut into my thumb with a bandsaw once when I was a kid. I pulled back as soon as I felt it, and the cut on my thumb wasn't even deep enough to warrant a band-aid. So if table saws scare you, get a bandsaw first.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
Use: White vinegar poured into a glass jar with steel wool that you have pulled apart and loosened. After fifteen minutes, brush onto the wood. After the surface is dry, you can leave it as-is or clear coat it with a product like Minwax One Coat Polyurethane. Distress prior to finishing, if so desired.http://www.wikihow.com/Age-Wood-With-Vinegar-and-Steel-Wool

Initially I thought a wine rack would be a finicky project to create, with the necessity of holding the bottles at a certain angle, etc. However, this ended up being a quick, easy and fun build. The shape of the bottles lets them rest on the rack at the correct angle (which is really only important when you are going to let your wine age). The simplicity of the design also allows you to see the labels on the bottles.


Since this 130 year old wood is painted on one surface I wanted to make sure it was sealed on all sides.  This old paint most likely contains lead.  It is always a good idea to seal both surfaces of a table top anyway to minimize warping from different rates of expansion and contraction.  Prior to sealing the top, it was sanded with 100, 150 and 220 grit sandpaper.  Two coats of Bullseye sealing shellac were applied to the top and bottom of the table top.  Two coats of Bullseye amber shellac and one coat of Bullseye clear shellac was applied to the table top after sealing.  Two coats of clear Briwax was rubbed into the top and buffed out for the final shine.
Hand saws are a good option for making quick cuts that don’t need to be perfectly straight. They do take some muscle as they are non-powered, but are perfect for a quick job. The downside to hand-saws is you will need a different saw for each type of material you need to cut, so if you’re trying to cut wood and sheet metal, that’s an additional cost.
Here is a look at the completed table prior to staining and sealing the piece. I also created matching benches to fit this table. The plans can be found by clicking here. I modified the width so they are a total of 69″ wide. Instead of using a 2×10 for the breadboards I use 2×8’s. Everything else was kept the same as Ana’s plans. The inside span of my table where the benches fit in is 73″ so that left 2 inches of wiggle room on each side of the bench so it can easily slide in and out.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Woodworking is based on a small number of core skills that when combined in various groupings make it possible for us to build a huge range of projects. Unfortunately, too many new woodworkers do not take the time to learn the core skills, opting to jump ahead of themselves to projects that seem more appealing at the moment. Very often, acquired bad habits and frustration are just around the corner.
Jigsaws have a reciprocating blade, and are a great do-it-all saw which we use them quite often on our projects. They excel at making oddly shaped cuts and curves, but aren’t so great if you need perfectly straight cuts. Another advantage to jigsaws is that the blades are small, cheap, and interchangeable so that you can quickly swap between cutting different materials.

There was one crack which required stabilization to prevent further splitting.  On an old piece of wood there is nothing more beautiful than a contrasting butterfly inlay to lock the pieces together.  Alternatively you could glue and clamp the split, however it is hard to get enough glue into the crack and an inlay looks much better.  I used a piece of bloodwood and an inlay jig on my router for the butterfly.  This was the first time I've tried inlay and it was very easy.  While the butterfly is beautiful & interesting, it acts functionally as 2 opposing wedges to prevent the crack from widening.  The last pic shows the finished product.
×