We tested this out on an old bathroom vanity - as we are over-capitalized on our home and just can't afford a full bathroom remodel. I lightly sanded the vanity, applied 4 coats of stain (allowing them to dry at least 24 hours between coats)with a foam brush, and switched out the vanity hardware. BEAUTIFUL! Our vanity looks brand new and very contemporary! This is a huge upgrade from that 90's "golden oak" color that is everywhere in our house.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.

We are moving into the new house, but with so many, many functional projects to tackle (like closets and pantry cabinets), a beautiful dining table is way down on the priority list.  But still, I insisited we need a dining table to move in.  Once you give in to the kids eating on the couch, you're done ... or at the very least have to be the bad guy and retrain the family.  
Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.
I think this is one of the best feelings if you are successful in making wooden spoon by yourself without any trouble. You can create stylish and unique spoon at home. The only thing is that you just need to follow some steps for making a perfect spoon. In this video, you can see how simply the making of a spoon is and how much you need time for making is explained in this video. 

If you want to get into woodworking, a good project to tackle is building your own workbench. It's really not that hard. So if building your own workbench is a bit too much work, or too intimidating, then take a step back and examine whether you really want to get into woodworking. This may be different if your goal is to cut silhouettes of kittens out of plywood with a scrollsaw, but I wouldn't call that sort of activity "woodworking".
Often you are in search of an outstanding and unique gift for your friends and family members. You need such gift which is the most admirable. I am introducing a puzzled shape bear and a duck, which can be used for decoration on the wall or you can use them as table mats. This gift is an amazing start for you in woodworking. It would look beautiful when its gift pack would be opened. I am sharing some of the examples of these pictures. Have a look at them.
Copyright 2018, Sarah Pawlak. Feel free to share what you see here but please only share one image with a link back to my page. It is not permissible to copy anything else on my site without first getting written permission from me. All printables are for personal use only. Sponsored posts always include my own thoughts and are never written by the sponsors. Affiliate links may be used at times. Pinning is always appreciated!! Thank you!
Have you ever heard about a chess which is made of wood? If not, then I am presenting a chess which is the most beneficial and attractive one. I am sharing its picture with you and you can make this chess very easily. The most amazing thing is that you can present it as a gift to other fellows. They would surely admire your gift. I am sharing some pictures of this chess; just have a look at these pictures. I am sure you would like these pictures.
Drawing inspiration from a round trestle table that was worth $3350, Rogue Engineer came up with their free DIY plan to make the table cheaper. Unexpectedly, you can make this excellent table for around $40. You may think that round tables are difficult to build, but if you have the proper tools and follow the instructions carefully as provided, you can actually make this table with ease.
We are moving into the new house, but with so many, many functional projects to tackle (like closets and pantry cabinets), a beautiful dining table is way down on the priority list.  But still, I insisited we need a dining table to move in.  Once you give in to the kids eating on the couch, you're done ... or at the very least have to be the bad guy and retrain the family.  
So I thought this would be the perfect project to try out my new sprayer on and, I’m telling you, friends…LIFE CHANGING.  I mean, I’ll be honest, there is a learning curve to spray painting.  There were some spots that I got a little too much paint and spots I didn’t quite get enough the first couple coats.  But, even with my amateur skills, this still saved me hours of time and looked WAY better than if I had brush painted.

Per usual, I used pocket screws to fasten the table top together after applying glue to the edges.  Pic 3 shows the underside of the table.  A straight edge clamp and a circular saw were used to trim the ends of the top.  The blue masking tape helps limit splintering from the saw.  To see if the table was square, I compared the diagonal measurements across the table top.  Diagonal measurements on a square or rectangle should be equal if the piece is square on all corners.  It's not very critical on a rustic, distressed table since the table's charm comes from it's imperfections.


Don't believe the mainstream thinking that hand tools are irrelevant, too slow to be useful, or less effective than power tools. Ignore, or at least take with a grain of salt, the power tool devotees who will say "There's a reason they invented power tools, ya know!" Your "shop" is a bench attached to the inside of a coat-closet door in a one-room studio apartment right now. Power tools are going to bother that nice med student next door, and that closet shop doesn't have any ventilation for the amount of dust you'll produce. Hand tools can be more efficient (in speed, quick access, storage, and lack of set up), they're quieter, and the pleasure of silence afforded by quiet hand tools--just a few soft noises produced by your tools--is a pleasure not to be overlooked. They're portable and will move with you, you'll learn more about how different types of wood behave, and, when you run into one of those power tool zealots, just go over to Todd's house and watch a few episodes of The Woodwright's Shop to get your respect for hand tools back in check.
Here is a look at the completed table prior to staining and sealing the piece. I also created matching benches to fit this table. The plans can be found by clicking here. I modified the width so they are a total of 69″ wide. Instead of using a 2×10 for the breadboards I use 2×8's. Everything else was kept the same as Ana's plans. The inside span of my table where the benches fit in is 73″ so that left 2 inches of wiggle room on each side of the bench so it can easily slide in and out.
This part is optional, but I like the little detail it adds.  I used a table saw to cut a line down the trimmed down 2×6.  I cut it about 1″ from the bottom.  I adjusted my table saw blade about 1/4″ high and ran it through, then adjusted slightly and ran it through again so that the groove was cut about 2 blade widths thick (slightly under 1/4″).  You could do this with a router instead if you wanted.
I love this barnwood reclaimed table-your husband did a beautiful job! We have a coffee table and two end tables (hand-me-downs) that remind me a little of this table. They each have metal legs that have criss-cross metal bars that make shelves below, and are great for holding baskets. The tops of each were pretty rough when we inherited the tables, and lately I’ve been thinking about either sanding and then white-washing the wood, and now after seeing your pictures I’m thinking more about just sanding the tops and see how they look and maybe finishing them like you did your table!? (I think I like your idea better! How many coats of Varathane did you folks use?) Thank you so much for sharing!
Choose a light-colored wood with interesting grain for the ball. It should be one solid piece, 2 1⁄2- to 3-in. square. I like to make more than one ornament at a time, so I use a rough blank about 8-in. long in order to make two balls. Make the cap and icicle from a contrasting dark wood that takes fine details. I like to use rosewood or ebony. You’ll need a piece that’s 1-in. square and 8-in. long.

Often when working with wood, after cutting it up and drilling holes the surface will be unfinished with unsightly burs and splinters. This is a simple fix with a quick sanding, but with a seemingly endless amount of types and grits of sandpaper and sanding equipment this can get confusing. The main types of sanders we’ll cover are belt sanders, orbit sanders, and hand sanders.

This wood bench plan is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. My neighbor saw a cute wood bench at a local restaurant and wanted one for her house.  She snapped a few pics for me, … [Read more...]
Scrollsaws are good for projects like cutting puzzles or silhouettes of cutesey animals out of wood. But for making furniture, scrollsaws just aren't up to the task. Scrollsaws, along with Dremel tools, do have their uses in crafts, but for woodworking, they are just a little too small. That said, Dremel tools are very useful for sharpening brad point drill bits, forstner bits, and bandsaw blades, so they do have a use in woodworking.
Have you heard about the wooden swords for decoration? If no, then I am sharing the picture of the wooden swords with you. This is an ideal gift for giving your loved ones. You can hang these swords on the wall and in the lobby. It looks great and gorgeous. Have a look at the pictures which I am sharing with you, I am sure you would like these pictures. These are the pictures which are best for wall decoration. So, you should choose these swords for giving the gifts to your loved ones.

If simplicity is your style with a hassle-free manufacturing process of your farmhouse table requiring less time, this free DIY plan from Instructables is another choice you can make to build your table. Even if you are a novice at making tables, this detailed illustrated instructions from Instructables with a list of the materials required will help you out.

Hybrid saws are essentially built like the old contractor saws, but with the motor in the cabinet, just like a cabinetmaker saw. They are much cheaper than cabinetmakers saws and not as heavy. The saw at left is my first table saw, a 40-year old contractor saw, which I enclosed on the bottom to keep the sawdust inside. At present, I use a hybrid table saw

We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!

Have you ever tried the projects that are unique and have some more modern looks? If you haven’t, I will show you some of the new and modern looking ideas which would surely admire you. Try these at your home and add the rare and unique items in your decoration. Here I am sharing 23 wood items with you and I hope you would enjoy the list. So, these modern look projects would give you a good start of making the modern woodworking items. Have a look at these woodworking ideas to get the amazing ideas.


I think you can see from all of these choices, the best solution is the one that works for YOU and your home. Just make sure you create an environment that makes you feel creative and excited to work. And while there are amazing workshops online for inspiration, don’t go crazy thinking your work area needs to be a renovation in and of itself! Use bits and pieces of inspiration, then get going on your projects!
The blade on a block plane, (click to enlarge drawing) commonly referred to as a plane iron, is mounted with the bevel side up to produce a cutting angle of about 37 degrees in a standard plane and 25 degrees in a low-angle plane. Some block planes feature an adjustable mouth, which allows the plane to be tuned for different cuts; Close the mouth and lower the blade for finish cuts or open the mouth and extend the blade for thicker rough cuts.
×