The bill of materials below assumes all the lumber is good. You should buy extra lumber to be able to leave out pieces with defects in them. In general, its best to buy wider pieces of lumber and rip them into narrower pieces, such as buying 2x6 and ripping the 2x3's out of them. You get much better lumber that way. It may be better to buy five 2x10x8' instead of the parts marked with an asterisk, and cut everything from those.
Here is a look at the completed table prior to staining and sealing the piece. I also created matching benches to fit this table. The plans can be found by clicking here. I modified the width so they are a total of 69″ wide. Instead of using a 2×10 for the breadboards I use 2×8's. Everything else was kept the same as Ana's plans. The inside span of my table where the benches fit in is 73″ so that left 2 inches of wiggle room on each side of the bench so it can easily slide in and out.
Through this project, you can convey a message for your love ones. You can make a whole name, a message or anything which you like most for conveying a message. You can make any kind of alphabet or numbers by using wood.All of you need a full command of handling woodworking project. You can give this frame to your love ones as a special gift for any occasion and the person who receives this will like itdefiantly. Basically, this concept is the mixture of art and creativity from wood. The creative mind can easily reach at the top level of woodworking project through a better way. You can see the full size of this image by following this link.
Build your own furniture, a dream of many but a reality for few. In this video I show you how I make farm tables. This is one made for a customer for a new house. It's 10 feet long and made from red oak, sawn from a dead standing tree. The base is made from spruce and yellow pine. It is constructed with mortise and tenon joints, using a hollow chisel mortiser and a tenon jig I made for the table saw. 

In regards to flattening the top, another technique would be take a pencil (soft lead) and lightly draw some big lazy squiggles across the top - enough so that there is a line every few inches. Then, use either a jointer plane or a belt sander to flatten the top until the squiggles are gone. The lines give you a reference to what is high and what is low - and when you are finished in a particular area. With the jointer plane, you want to stroke at about 45 degrees to the grain of the wood, and with a belt sander, you want to keep the sander flat on it's platen (don't let it tilt and dig in) and use wide, arcing, sideways sweeps with very light pressure - again at about 45 degrees to the grain of the wood - never let the sander start or stop when in contact with the surface. In both cases, finish with light sanding with either a belt sander, linear sander, or by hand, stroking in the direction of the grain. Palm sanders can leave swirls.
Life Storage has come with a perfect mix of rustic designs and materials with a touch of modern furniture style. The timeless elements and cleanliness give a trendy look. If you can afford $300 for a farmhouse table, this free plan is ideal for you. Even if you are a beginner, you can build this 10-seater farmhouse table which acts for storage as well.
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com. 

You're going to connect the two leg–apron assemblies to the stretchers using cross lap joints. These are among the easiest and most forgiving of wood joints to make, and they're also quite sturdy. Mark the joint positions on the legs and stretchers. Start the half-lap joints on the legs by notching the two outside lines with a circular saw set to a depth of 1½ inches. Guide the saw using a triangular rafter square. Between the two outside cuts make a series of relief cuts spaced ⅛ inch apart (fig. 3). Then use a sharp chisel to chop away the waste (fig. 4). When you cut the half-lap joints on the short stretcher, set the saw's depth to 1⅜ inches deep. This will make the stretcher extend ⅝ inch past the surface of the leg when the table is finally assembled. The offset will give you a table that looks like it was built by a farmer rather than by West Elm. It'll look nice. 

Wow, this is really big rolling dice and the special thing of this dice is that it is made from wood. I think wooden dice are durable dice. This is one of the best decorations I have ever found. The main question is that why it is so special for me? Basically, I am a game lover and I have made this wooden dice for the decoration of home. The size of this dice is large instead of normal games dice. This is really special project for me that am the reason I make it with full charm. You can see the full image of beautiful dice in the following link.
The blade on a block plane, (click to enlarge drawing) commonly referred to as a plane iron, is mounted with the bevel side up to produce a cutting angle of about 37 degrees in a standard plane and 25 degrees in a low-angle plane. Some block planes feature an adjustable mouth, which allows the plane to be tuned for different cuts; Close the mouth and lower the blade for finish cuts or open the mouth and extend the blade for thicker rough cuts.
Just look at this small and cute helicopter that is made of wood. I am sure you would enjoy having it. Your kids would play with this. If you are giving gifts to your friend on the birthday of his/her child, then it is the best gift. I am sure your friend would admire this gift and their kids would just love having it. There are different colors of this helicopter. I am sharing some of the pictures of this helicopter. Have a look at these pictures and get an idea about it.
In my design, I considered 3 different types of legs made from 30" long cedar 4x4s.  (You could use other types of wood including gluing three 2x4s together to make solid legs.)  The simplest design was to cut the legs to length and use the 4x4s square.  Second was to taper the two inside surfaces and third was to taper all four surfaces.  I ended up tapering all 4 sides on my bandsaw.  The cut line begins 4" from the top and removes 1/2" at the bottom.  Pic 2 shows how little I removed.  I wanted the legs to have "shape" while remaining stout in appearance and this slight taper seemed about right.  Pic 2 also shows the levelers in the bottom of these legs which were salvaged from a previous project.  I decided to leave the levelers and shortened the legs a bit.

The shop you see in the layout is my current setup and has evolved over many years to accommodate most importantly the acquisition of newer equipment but also better work flow. It is a free standing two story traditional barn style with office and storage space on the second level. Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
If you want to get into woodworking, a good project to tackle is building your own workbench. It's really not that hard. So if building your own workbench is a bit too much work, or too intimidating, then take a step back and examine whether you really want to get into woodworking. This may be different if your goal is to cut silhouettes of kittens out of plywood with a scrollsaw, but I wouldn't call that sort of activity "woodworking".
If you're dreaming of a white Christmas, prep your home with this practical and pleasing boot rack. Blogger Stephanie Lynn constructed this fixture from stock lumber and 2-inch dowels to keep the slush and mud outside the house, where they belong. Glue down the dowels, or leave them dry-fitted so you can disassemble and store the rack easily during the summer months.

This wooden sofa side table can also be made in different sizes and shapes as you can find on the internet. Some of the items you will need for this project are wooden pieces, cutter, screws, etc. We have included a video tutorial here that illustrates the process of building a wooden sofa side table. This is not the exact one that you see in the image above, but it can be modified to build any shape or design you want. The video tutorial also has English subtitles to make it easy for anyone to understand and follow the steps.
Keep in mind that always choose simple and easy step tutorial for making any kind of project. This brings beneficial for making a different project. For those how don’t know about how to make perfect jewelry tree are suggested to try something easy and simple tutorial. You can also make jewelry hanging from recycling things. It depends on your creative mind that what step you are choosing for making a perfect project.
Hardwood boards and softwoods may look similar in shape and dimension, but they are sold using completely different measuring systems. Softwoods are typically sold in standard lumber dimensions (such as a 2x4), whereas hardwoods are most often sold by the board foot. Calculating board feet helps you guarantee that you're getting your money's worth on every piece of hardwood you purchase.
From day one you've wondered how can you be both a tree hugger and a woodworker, how you can respect nature while also using and working within nature (not roping all of it off limits), as Wendell Berry professes. In Illinois, there is a family-owned and run company called Horigan Urban Forest Products that dries and mills old-growth wood from trees felled in the Midwest's awesome spring tornado season, and summer and fall thunderstorms. There are many sources of wood like this all over the world, and sometimes they're more expensive, but old-growth wood is going to be.

The first – and some say the most important choice in designing a dining table is size.  Since our tables are made-to-order we can offer a farmhouse table in any size, shape, style or color.  Do you need a 12 foot table, 72″ round pedestal table, a narrow 32″ wide trestle table, a 36″ high counter height table?  Large, long, narrow, small, square, round, oval tables.  All no problem.  We can make any of these and more.   Farmhouse tables are available as either new wood tables or old reclaimed wood.    


This table is designed to be gorgeous. The table might look challenging to build, but if you follow the plan, it is very easy. If you check Step 1, you will find that cutting the joints can be done quickly and a 4 x 4 X-leg can be built with lap joint. This provides stability and durability. Moreover, the herringbone top makes the table even more beautiful.
Work with attention and don’t forget that a good planning will save you from many issues and it will keep the costs within your budget. Invest in high quality materials, such as pine, redwood or cedar. Drill pocket holes before inserting the galvanized screws, to prevent the wood from splitting. Add waterproof glue to the joints, in order to enhance the rigidity of the structure.
It's nice to be on your site getting plans and building projects.  I was so inspired by you I went out and bought Ryobi tools, and have since built 3 projects all on http://www.Ana-White.com/ by you.  I loved building the Potting Table, and better yet my Mother loved it when I gave it to her as a gift.  I am now working on the Farm House style Table and Benches.  I can't wait to see how they turn out!  

So many ideas are included in this website, just waiting for you to build memories with inexpensive wood projects. You will find a variety including outdoor projects, furniture plans, household accessories, craft fair items and workshop furnishings.  There is also a host of projects suitable for a beginner. Build one of these great projects this weekend!

A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.

This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
Creating custom picture frames for friends and family is a great gift giving project that's sure to please even those difficult to shop for gift recipients. Everyone has a special photo or keepsake they've meant to have framed. Making a custom frame to match may be the best gift of the season. Best of all, it's a quick and simple project to complete with the right tools and set up.
A smart wooden table is a very useful wooden item for every household. You can yourself make a nice, strong and beautiful wooden table suitable for any purpose. As you can see the image, it is a small, yet good enough table to be used as a study table, coffee table, lamp stand, breakfast table, etc. You can also find many other design variants on the internet. Choose the one you want for yourself and start making it now.It is actually very easy and interesting to make. Size, shape and designs are according to your choice when you made it.
Chances are in any woodworking project, you’re going to have to connect two pieces of material. Screws are ideal for this – much better than nails – but there are hundreds of different types and sizes, all for different applications. We will review the most common types and applications so that you can quickly determine what type you will need for your project and how to use it.
The video above includes a step-by-step tutorial for making a wooden toy house. By following these steps, you can easily make it by yourself. You will also need some basic woodworking items, such as wood, pop sticks, cutter, glue and screws, etc. Even if you do not like this one, you can always browse the internet for more beautiful wooden toy houses ideas. I have also shared a link where you can find some really interesting and beautiful wooden houses ideas for every kind. Just select the one you like the most and start building.
Finally, a word on glues: You might want to do some experimenting with polyurethane glue instead of aliphatic resin (wood) glue. Polyurethane glues require a slightly different work flow, but since switching to polyurethane about 15 years ago, I can't see going back. I use aliphatic glues for some things (like biscuit joints) - but not very often. Polyurethane glues actually harden (aliphatic resins remain "liquid"), poly takes stain like wood (no bright areas where the stain wouldn't bond to the glue lines), poly doesn't dull tools or gum up sandpaper, poly is waterproof and can fill minor gaps. My favorite brand, so far, is Gorilla Glue.
This video shows the making of wooden hanging with one of the easiest ways. I make this wooden stylish wooden hanging at home easily and decorate with the variety things that give fabulous look to my room. You can also make it by using basic tools like wood cutters, hammer, drill and measuring tape. I made it at home for my creativity in easy steps. It is actually very easy and interesting to make. Size, shape and design is according to your choice when you made it.
Living in South Florida gives me the ability to work under the bright Florida sun by simply rolling the woodworking power tools out from under the roof. On days like the one when this photo was taken, when rain is expected later in the afternoon, most of the tools can be kept under the roof, and rolled away into large lockable storage rooms in less than five minutes.
As you hear the term “farmhouse table”, you think about a traditional table. Moreover, if you like the traditional style of your furniture, this is a perfect DIY plan from Popular Mechanics for your farmhouse table. The design is very basic, and you can easily make this table even if this is your first woodworking project. The detailed instructions with illustrations are provided along with the materials and tools required to accomplish the task. This table offers enough space for at least six people to sit comfortably and it will be one of the greatest additions to your dining space.
Through this project, you can convey a message for your love ones. You can make a whole name, a message or anything which you like most for conveying a message. You can make any kind of alphabet or numbers by using wood.All of you need a full command of handling woodworking project. You can give this frame to your love ones as a special gift for any occasion and the person who receives this will like itdefiantly. Basically, this concept is the mixture of art and creativity from wood. The creative mind can easily reach at the top level of woodworking project through a better way. You can see the full size of this image by following this link.
The router might just be the most versatile woodworking power tool there is and it's a great first tool for beginner woodworkers. When set up properly and safely handled, a router can do everything from cutting joinery to shaping parts. Just be sure you understand the basic safety procedures and read the tool's manual if you're new to using a router.
I have been involved one way or another with woodworking for the last six decades, it began when I was about ten years old, my father built me a jigsaw by modifying an old Briggs and Stratton engine. Looking back I don't believe it cost him anything more than the price of a few welding rods to give me hours of entertainment cutting doodads out of apple box wood. The last three have been limited due to health reasons but I still do small projects when necessary.

This table is designed to be gorgeous. The table might look challenging to build, but if you follow the plan, it is very easy. If you check Step 1, you will find that cutting the joints can be done quickly and a 4 x 4 X-leg can be built with lap joint. This provides stability and durability. Moreover, the herringbone top makes the table even more beautiful.
But first, this build was sponsored by Timber Wolf Forest Products.  They provided the legs for the build.  Also, HomeRight provided the paint sprayer for this project.  All opinions are my own and are uninfluenced.  This post also contains affiliate links.  See disclosure policy for details.  If you purchase from these links, I may receive a small commission at no extra cost to you.  This helps keep the content on this site free.  Thank you for your support and for supporting the brands that help support this site.
Hey I love this article,Thanks. 4 months ago, I started looking for woodworking. The industry is extremely interesting but I have problems with how I can do it.My uncle who has been doing more than me in this industry, has suggested to me to follow Teds plans, Do you think it’s a good move to follow these plans? ? I keep reading good reviews about Teds Plans but I am unsure if it will still work on me.At this time I can purchase these plans at a very low price,so if possible can you leave me feedback on wether I should do it or not. It would mean a lot coming from an expert in this field.

There are different grades of tools available at different prices. Salesmen will probably tell you to get good quality tools that last a lifetime. But the price difference between a cheap tool and a good quality tool can easily be a factor of four. My advice is to get cheap tools first and use them until they break. Once they break, it's time to consider getting something better. But unless you are a professional who uses the tools every day, even a cheap tool is likely to last a long time.


A nice thing about a bandsaw is that it's not scary to use. Sure, a bandsaw can cut your fingers off too, but it will probably cut your finger slow enough that you can pull it back before it's a major injury. I cut into my thumb with a bandsaw once when I was a kid. I pulled back as soon as I felt it, and the cut on my thumb wasn't even deep enough to warrant a band-aid. So if table saws scare you, get a bandsaw first.
Houses aren’t really scaled practically for small children; countertops, sinks and cabinets are just too high for them to use comfortably. Fortunately, you can remedy the problem in an afternoon. A simple, classic step stool like this one is just right for putting everything within reach of the little ones. It’s even sturdy enough for an adult needing a few more inches to reach those top cupboard shelves.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.

We are moving into the new house, but with so many, many functional projects to tackle (like closets and pantry cabinets), a beautiful dining table is way down on the priority list.  But still, I insisited we need a dining table to move in.  Once you give in to the kids eating on the couch, you're done ... or at the very least have to be the bad guy and retrain the family.  


I used a #00 Steel Wool and White Vinegar solution to patina the wood and give it an aged look. Put a good handful of steel wool in a jar and add white vinegar. Let the vinegar dilute the steel wool for at least 3 to 4 days. The mixture will get darker the longer you let it sit. I let mine sit for a full week. Once diluted, simply brush the mixture on your piece. Oxidation will occur as the mixture reacts with the tannins in the wood to give it variations in color.
Table saws, band saws, and radial-arm saws are examples of woodworking machines that are most often used exclusively in a wood shop because they are far too large and cumbersome to be portable. Even though they're confined to the shop, these workhorses are so useful that it makes sense to complete a woodworking project in the shop and carry the finished piece to the location or job site where it will be used or installed. 

The most useful stationary tools are a drill press and a table saw. For the longest time, I only had a cheap old contractor saw, and only a very small drill press, but I made do with those. The difference between a good drill press and a cheap drill press is much smaller than the difference between a cheap drill press and no drill press, so don't wait until you can afford the perfect one.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
This design looks extremely stylish which you will want to sport in your kitchen or living space. However, you might think it will be difficult to make this stylish three pedestal table but stay rest assured, even if you are a novice at woodworking, you can create this project with ease. The design is extremely simple to make and brings a charming feel to your room.
Methods for skinning a cat have nothing on ways to build a bench. Explore different joinery methods and work with those that you are able to complete the best. Don't overcomplicate something when it doesn't need to be. There's a reason tools have improved, glue has gotten better, fasteners stronger, and new joinery methods have been introduced. A lot of the time the focus in woodworking is on finding shortcuts to get the same or better results. Don't let joinery snobs influence you.
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
From my point of view, I think this is really a different project because normally you will find only one wooden item like a chair, or a table, but in this project, you will find two wooden items. The combination of table and chair is really beneficial for me. I wanted to try something different project from my daily routine life and here in this image, you will find the full-size image of this project so you came to know that I am successful in making chair plus table project.
Building a Wooden baby cot is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and baby cot by myself. This creativity saves a lot of money. And believe me when I say this; you can also manage to make wonderful wooden items with a little practice and some woodworking experience. This baby cot can also be made in different sizes and shapes as you can find on the internet.
It's nice to be on your site getting plans and building projects.  I was so inspired by you I went out and bought Ryobi tools, and have since built 3 projects all on http://www.Ana-White.com/ by you.  I loved building the Potting Table, and better yet my Mother loved it when I gave it to her as a gift.  I am now working on the Farm House style Table and Benches.  I can't wait to see how they turn out!  
This video shows the making of wooden hanging with one of the easiest ways. I make this wooden stylish wooden hanging at home easily and decorate with the variety things that give fabulous look to my room. You can also make it by using basic tools like wood cutters, hammer, drill and measuring tape. I made it at home for my creativity in easy steps. It is actually very easy and interesting to make. Size, shape and design is according to your choice when you made it.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished. 

Getting started in woodworking can seem like a daunting task. From specialty woodworking tools to identifying and understanding the different types of wood, there is so much to know that even the old-timers are still developing. But learning and experimenting are what woodworking is all about. Get started on the right foot with some essential basics about safety, tools, lumber, and traditional layout and measuring techniques.
A good tool to get next is some sort of circular saw. A circular saw cuts a lot faster than a jigsaw, and it's easier to make a straighter cleaner cut with it. It's also a very useful tool for cutting up big sheets of plywood, even if you already have a table saw. At this point, you have enough tools for some simple projects such as this table or some storage shelving
A luminaria (often called luminary) is a traditional Mexican lantern made from a paper bag with sand and a candle inside. We’ve add some woodworking panache to these outdoor accents and build our luminarias from wood, with box joints and a star-shaped cutout. They’re beautiful — and reusable — ways to brighten patios, steps and walkways this holiday season.
In my project section I wrote an article about small boxes made with a router. The article was written years ago and the boxes were made several years before that. Thus, I had to use one of those old boxes to write this article as I couldn't exactly remember how I made them. The initial construction process came from that great Canadian TV show, The Router Workshop, but the jig I use was born of necessity. One year I decided to build a pile of these boxes and enter a craft fair. After two or three, I decided there had to be a faster way to set up for the cuts, so I used a discarded table saw sled to fashion the jig in this article.
#00 Steel Wool and White Vinegar – Put a handful of steel wool in a jar and add white vinegar. Let the vinegar dilute the steel wool for at least a couple days. The mixture will get darker the longer you let it sit. Once diluted, simply paint the mixture on your piece. Oxidation will occur and the mixture reacts with the tannins in the wood to give it variations in color. It changed the Fir wood to dark blues, greys, browns, and black. Do not use white Pine because it will not darken much at all.

But first, this build was sponsored by Timber Wolf Forest Products.  They provided the legs for the build.  Also, HomeRight provided the paint sprayer for this project.  All opinions are my own and are uninfluenced.  This post also contains affiliate links.  See disclosure policy for details.  If you purchase from these links, I may receive a small commission at no extra cost to you.  This helps keep the content on this site free.  Thank you for your support and for supporting the brands that help support this site.


As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.The final piece looks like the one in the image. It is absolutely loveable. The design, color and looks can also be modified to suit the surrounding area.

Because these legs were salvaged they had old screw holes in them which were filled prior to painting.  In retrospect, it probably would have looked cool to just leave them.  I lightly sanded the legs with 100 & 150 grit sandpaper which smoothed them without removing all the saw marks.  One coat of chalk paint and 2 coats of clear Briwax was used to finish the legs.  Briwax yellows the finish a bit which aged the paint nicely.  Between coats of Briwax I sanded through the paint on some of the edges with 100 grit paper to show wear.  
I’ve included the option to purchase the amplified plan for $19.99. The amplified plan is a printable plan that will guide you every step of the way and is packed with tips, tricks, money saving options, and answers to frequently asked questions. I know it’s hard to believe but its got even more helpful info than the plans below! Plus it’s a great way to support this site so we can continue to put out free DIY projects every week!
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Build your own furniture, a dream of many but a reality for few. In this video I show you how I make farm tables. This is one made for a customer for a new house. It's 10 feet long and made from red oak, sawn from a dead standing tree. The base is made from spruce and yellow pine. It is constructed with mortise and tenon joints, using a hollow chisel mortiser and a tenon jig I made for the table saw.
×