The blade on a block plane, (click to enlarge drawing) commonly referred to as a plane iron, is mounted with the bevel side up to produce a cutting angle of about 37 degrees in a standard plane and 25 degrees in a low-angle plane. Some block planes feature an adjustable mouth, which allows the plane to be tuned for different cuts; Close the mouth and lower the blade for finish cuts or open the mouth and extend the blade for thicker rough cuts.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.

Cordless tools are very handy, and I love my cordless drills. However, if you are just dabbling with getting into woodworking, and you may only use your tools every six months, you may find the litium batteries dying prematurely. Litium batteries slowly self-discharge, and once fully discharged, they are permanently damaged. So if, for example, you use a cordless drill until the battery is low, put it away without recharging, and try to charge it again months later, you may find the battery no longer able to take a charge.


Douglas fir from home improvement centers will almost always warp when you try to make a flat top. It is never dried to the same extent as hardwood and ships out for the purpose of being used as framing lumber, not furniture lumber. That said, you can do it, but buy it and let it sit in your garage for a few months or longer to let it further dry and acclimate to your environment. Even better if you plane it down after that waiting period, then allowing it to acclimate for another week or so to make it works out all of its twists prior to being turned into a top. Do you have any hardwood dealers in your area? Try visiting one and make an investment in your table...buy some good maple (soft maple is worlds harder than new douglas fir - you don't need hard maple, ie:or sugar/rock maple).
Another classic game! (Are you picking up on a trend?). A cribbage board is really just a piece of wood with 240-plus holes drilled in it. This project includes files necessary to program a CNC machine to drill all the holes, but it also includes a template for boring the holes with a drill. There are endless opportunities for customizing this project with different species of wood. All this adds up to the fact that cribbage boards make great gifts.
Woodworking is accessible to people of all ages, skill levels, and budget. Don't expect to be the Wood Whisperer overnight, but there are plenty of woodworking websites that offer free plans and tutorials to help you every step of the way. One of these sites is Chief's Shop from Chris Hill, who has been a woodworker his entire life. He offers some great advice for woodworking newbies, which is also a great reminder for those with a bit more experience:
While driving the car, you always need a keychain and in your home it is also a basic necessity. Often you keep your important keys in the keychain and you can carry this key chain everywhere. I am sharing such a key chain with you which is really an astonishing one as it is in the shape of a USB. You can have keys in it and hang it on the wall hanging. You can also give this key chain as a gift to your friends.This key chain is very easy and simple to make. So, do not hesitate while making it. I am sharing some pictures of this key chain with you, let’s have a look at these pictures.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
Initially I thought a wine rack would be a finicky project to create, with the necessity of holding the bottles at a certain angle, etc. However, this ended up being a quick, easy and fun build. The shape of the bottles lets them rest on the rack at the correct angle (which is really only important when you are going to let your wine age). The simplicity of the design also allows you to see the labels on the bottles.
From my point of view, I think this is really a different project because normally you will find only one wooden item like a chair, or a table, but in this project, you will find two wooden items. The combination of table and chair is really beneficial for me. I wanted to try something different project from my daily routine life and here in this image, you will find the full-size image of this project so you came to know that I am successful in making chair plus table project.
The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?
Scrollsaws are good for projects like cutting puzzles or silhouettes of cutesey animals out of wood. But for making furniture, scrollsaws just aren't up to the task. Scrollsaws, along with Dremel tools, do have their uses in crafts, but for woodworking, they are just a little too small. That said, Dremel tools are very useful for sharpening brad point drill bits, forstner bits, and bandsaw blades, so they do have a use in woodworking.
My own personal shop is a 20x20 section of my garage. Some people might argue that I've got plenty of space, but those people obviously feel their lives are complete without owning a panel saw. I'm not judging. I'm just saying that panel saws are awesome. And even with four-hundred square feet I need to find some creative storage solutions in the shop to accommodate my power tool addiction. There are plenty of people who have done a lot more with a lot less. Here are some of my favorite space saving workshop ideas.
Disclaimer: Almost any DIY project involves risk of some sort. Your tools, materials, and skills will vary, as will the conditions at your project site. Rogue Engineer has made every effort to be complete and accurate in the instructions provided on this website. Rogue Engineer will not assume any responsibility or liability for damages or losses sustained or incurred in the course of your project or in the use of the item you create. Always follow the manufacturer's operating instructions in the use of tools, check and follow your local building codes, and observe all commonly accepted safety precautions. 

Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.
To start, make a base assembly out of the aprons, legs, and stretchers. Attach one leg on either side of one of the short aprons. Bore two holes for pocket screws into each side of the apron's back, four in total (fig. 1). Clamp the legs to the apron, but add a ⅛-inch piece of wood to the front as a spacer (fig. 2). This will offset the face of the apron from the face of the leg, pushing it back a bit and creating a nice dimensionality. Drive the pocket screws through the apron into the leg. Repeat the same procedure for the second leg–apron assembly.
Moving up to the next level, the next machine to get would be a jointer planer. A jointer planer is very important if you want to glue up pieces of wood side-by-side to make panels. It's just plain all around handy for planing stock. I'd recommend you get a jointer planer before you get a thickness planer, because there is so much more that can be done with a jointer than a thickness planer. A thickness planer is really handy to get stock to the right thickness, although in a pinch, that can also be done on the table saw by putting the workpiece between the fence and the blade. If you cut from both sides, you can thickness stock up to twice the maximum depth of cut of your table saw.
The video above includes a step-by-step tutorial for making a wooden toy house. By following these steps, you can easily make it by yourself. You will also need some basic woodworking items, such as wood, pop sticks, cutter, glue and screws, etc. Even if you do not like this one, you can always browse the internet for more beautiful wooden toy houses ideas. I have also shared a link where you can find some really interesting and beautiful wooden houses ideas for every kind. Just select the one you like the most and start building.
After cutting the rabbet joints, we walk you through the glue-up and assembly of the box. This critical stage in the process involves applying glue to the box parts and using clamps to hold the parts together while the glue dries. The assembly and glue-up tips that we detail in this episode -- and our companion article -- can apply to the assembly of any woodworking project.
Through this project, you can convey a message for your love ones. You can make a whole name, a message or anything which you like most for conveying a message. You can make any kind of alphabet or numbers by using wood.All of you need a full command of handling woodworking project. You can give this frame to your love ones as a special gift for any occasion and the person who receives this will like itdefiantly. Basically, this concept is the mixture of art and creativity from wood. The creative mind can easily reach at the top level of woodworking project through a better way. You can see the full size of this image by following this link.
Super Chunky X Table Plans and Tool Review is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. During this build, I'll be reviewing the Ridgid MegaMax, Diablo blades, Bosch drill bits and Makita … [Read more...]
This video shows the making of wooden hanging with one of the easiest ways. I make this wooden stylish wooden hanging at home easily and decorate with the variety things that give fabulous look to my room. You can also make it by using basic tools like wood cutters, hammer, drill and measuring tape. I made it at home for my creativity in easy steps. It is actually very easy and interesting to make. Size, shape and design is according to your choice when you made it.
×