We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
Since this 130 year old wood is painted on one surface I wanted to make sure it was sealed on all sides.  This old paint most likely contains lead.  It is always a good idea to seal both surfaces of a table top anyway to minimize warping from different rates of expansion and contraction.  Prior to sealing the top, it was sanded with 100, 150 and 220 grit sandpaper.  Two coats of Bullseye sealing shellac were applied to the top and bottom of the table top.  Two coats of Bullseye amber shellac and one coat of Bullseye clear shellac was applied to the table top after sealing.  Two coats of clear Briwax was rubbed into the top and buffed out for the final shine.
Because these legs were salvaged they had old screw holes in them which were filled prior to painting.  In retrospect, it probably would have looked cool to just leave them.  I lightly sanded the legs with 100 & 150 grit sandpaper which smoothed them without removing all the saw marks.  One coat of chalk paint and 2 coats of clear Briwax was used to finish the legs.  Briwax yellows the finish a bit which aged the paint nicely.  Between coats of Briwax I sanded through the paint on some of the edges with 100 grit paper to show wear.  

I love this barnwood reclaimed table-your husband did a beautiful job! We have a coffee table and two end tables (hand-me-downs) that remind me a little of this table. They each have metal legs that have criss-cross metal bars that make shelves below, and are great for holding baskets. The tops of each were pretty rough when we inherited the tables, and lately I’ve been thinking about either sanding and then white-washing the wood, and now after seeing your pictures I’m thinking more about just sanding the tops and see how they look and maybe finishing them like you did your table!? (I think I like your idea better! How many coats of Varathane did you folks use?) Thank you so much for sharing!

The shop you see in the layout is my current setup and has evolved over many years to accommodate most importantly the acquisition of newer equipment but also better work flow. It is a free standing two story traditional barn style with office and storage space on the second level. Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools.
It was murderously hot here in the Charm City suburbs last weekend. The heat index topped a full 115 degrees on Saturday. But fear not, the heat didn’t deter us from tackling our long-awaited shed storage shelves project. We’re excited about this project because we’ve been looking forward to sharing a plywood shelving article for some time now, and this article gives us the perfect avenue for that. In case you’ve forgotten (or more likely if you’ve just started reading here), here’s the new shed. It looks great on the outside, but without some shelving and storage hooks for tools inside, most of the interior space would go to waste.

The cost of being disorganized is time. It takes me ten times as long to work on a project when I am scouring the room looking for a drill bit, the right screws, or trying to remember where I last used one of my 10 tape measures. Workshop organization is an ongoing project. As you acquire more tools, you have to rearrange your shop to work in storage for those new items. So mobile and modular storage, wherever possible will save you time down the road. Here are some amazing Workshop Organization Ideas that I hope will inspire you!

I wanted to have something elegant stuff made of wood then I just found this round and triangle shape table. This project is really different because it represents two shapes. When you use this table in your home everybody will appreciate your choice and everybody wishes to have a table like this. The edges of this table are in a triangle shape and front you will see in round shape.
Through this project, you can convey a message for your love ones. You can make a whole name, a message or anything which you like most for conveying a message. You can make any kind of alphabet or numbers by using wood.All of you need a full command of handling woodworking project. You can give this frame to your love ones as a special gift for any occasion and the person who receives this will like itdefiantly. Basically, this concept is the mixture of art and creativity from wood. The creative mind can easily reach at the top level of woodworking project through a better way. You can see the full size of this image by following this link.

Need a farm table for a nook?  A pedestal table table works great.  Looking to seat a lot of people?  A trestle table could be the right solution for you.  All of our base options come in a variety of design styles to fit your specific interior design requirements.  If you can’t find what you need, send as picture of what you have in mind and we may be able to design a base for you.  Not sure what base would work best for you?  Our table consultants are here to help!


The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Whether your work area is a dedicated shop or a temporary cleared space in the basement or garage safety has to be the number one concern. A clean shop is a safe shop, spend a few minutes at the end of the day picking up and sweeping the floor. This not only cleans your surroundings, it also clears your mind, the solution to that problem you had earlier may suddenly appear.

Creating custom picture frames for friends and family is a great gift giving project that's sure to please even those difficult to shop for gift recipients. Everyone has a special photo or keepsake they've meant to have framed. Making a custom frame to match may be the best gift of the season. Best of all, it's a quick and simple project to complete with the right tools and set up.
I’ve included the option to purchase the amplified plan for $19.99. The amplified plan is a printable plan that will guide you every step of the way and is packed with tips, tricks, money saving options, and answers to frequently asked questions. I know it’s hard to believe but its got even more helpful info than the plans below! Plus it’s a great way to support this site so we can continue to put out free DIY projects every week!
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project. 

While you can purchase pre-surfaced lumber at your local home center, there are several benefits to buying rough-sawn lumber from a hardwood dealer and milling it to size in your shop. Rough-sawn lumber is typically less expensive than pre-surfaced lumber. And rough-sawn lumber can be milled to custom thickness giving you more flexibility with your woodworking designs. Check out this video for a detailed explanation on how lumber is cut and sold, including how to speak like a pro at the lumberyard and how to calculate a board foot.

Liz Fourez started Love Grows Wild in 2012 with a passion for interior design and homemaking and a dream to help others create a home they love.  From simple project tutorials, to holiday and entertaining ideas, to her journey renovating a 1940’s farmhouse, Liz demonstrates how to create a beautiful and inviting home with a handmade touch. She turned her signature cozy, neutral style into a best-selling book in 2016 and continues to inspire readers with her captivating photography and easy decorating ideas. Read more about Liz > > > >
There are also project books that provide fun new ideas to play with on the scrollsaw, and the fun is made even better when you’re being productive by making gifts at the same time. If you’re a carver, there are many project ideas available to you, as well. There are also Christmas projects for the woodturner. One popular idea is to make ornaments for your tree—or someone else’s. There are several books that will provide help specifically for making ornaments. You’ll find that woodturning allows an opportunity for endless creativity! You can find a variety of kits available, and then you can use whatever material you prefer to turn and then shape and finish any ornament you can imagine!
×