We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!

This table is a little narrower than I would have liked for it's length (34x72), but it's perfectly sized for the space we are using it in.  At 72" long, I would have preferred something closer to 40" wide but this works for us.  The top is made from 16" wide soffet boards from a house I helped tear down when I was 10 yrs old (no, it wasn't the house we were living in).  The old boards have been in the barn for 40 years and needed to be used.  The center painted board is also from the same house.  

Liz, Great job on your new table and benches. They really look great. Love the chandelier also. Wanted to let you know that after I saw your tutorial on the board and batten in your living room and dining room, it really inspired me. I said to myself, “I can do that.” So, with that in mind, I am just finishing up board and batten in my laundry room. It was really an easy project and I love the results. It really perks up a drab old laundry room. I ended up doing all the work myself. The only help I asked my husband for, was with the nail gun, as we had to really get into some tight places. All in all, though, I am very pleased with it. Thanks for the idea.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
The video above includes a step-by-step tutorial for making a wooden toy house. By following these steps, you can easily make it by yourself. You will also need some basic woodworking items, such as wood, pop sticks, cutter, glue and screws, etc. Even if you do not like this one, you can always browse the internet for more beautiful wooden toy houses ideas. I have also shared a link where you can find some really interesting and beautiful wooden houses ideas for every kind. Just select the one you like the most and start building.
So, what is a warping board? It is a very basic frame (that can be joined together by any number of methods) with a bunch of pegs poking out of it. Weavers use it as a quick and easy way to measure out a great many pieces of string or yarn, all of the same length. These are then installed into the loom as the warp, hence the name warping board. It all sounds very simple, and looks that way too, unless you approach the design scientifically – my usual mistake.
The article explains step by step process for making this awesome piece of wooden art. It is actually very easy to make one.This tutorial shows the making of wooden box with one of the easiest ways. However, it is a bit difficult to make them, but not so much.I make this wooden box at home easily. You can also make it by using basic tools like wood cutters, hammer, drill and measuring tape. I made it at home for my creativity in easy steps.
Liz, Great job on your new table and benches. They really look great. Love the chandelier also. Wanted to let you know that after I saw your tutorial on the board and batten in your living room and dining room, it really inspired me. I said to myself, “I can do that.” So, with that in mind, I am just finishing up board and batten in my laundry room. It was really an easy project and I love the results. It really perks up a drab old laundry room. I ended up doing all the work myself. The only help I asked my husband for, was with the nail gun, as we had to really get into some tight places. All in all, though, I am very pleased with it. Thanks for the idea.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Often you are in search of an outstanding and unique gift for your friends and family members. You need such gift which is the most admirable. I am introducing a puzzled shape bear and a duck, which can be used for decoration on the wall or you can use them as table mats. This gift is an amazing start for you in woodworking. It would look beautiful when its gift pack would be opened. I am sharing some of the examples of these pictures. Have a look at them.
I few years ago I made a build plan for Remodelaholic for a super adorable House Frame Bed. The build plan was inspired by this darling room shared by an Australian magazine, Home Life.  Over the years a few requests have been made for a full size mattress version. Here it is --> How to Build a House Frame Bed - Full Size This bed is designed to fit a full mattress 53" x … [Read more...]
As you can see in the image, this beautiful heart shaped wall hanging wooden piece on the wall. It looks beautiful and can be used to surprise someone special. The shape and design of this wooden hanging depend on how properly you build it. First time workers definitely need some guidance to help them with the process. You can choose the wood type, color and design as you like for your project. You can easily make it at home by using some artthings. You can decorate your wall hangings with different materials, designs and styles. I am actually making one of this wooden heart shaped hanging in my home. It is perfectly cool and artistic work. These hangings may be adjustable or a fixed.
This cute earring box is the ideal one for giving the gifts to your loved ones. Have you ever given your gift in a wooden jewelry box? When you meet with your friends and family it is a very great idea to surprise them with such gifts. They would really admire your selection. I am sharing some of the pictures with you, which are about this earring box. Have a look at these pictures; I am sure you would like them.

Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
Table aprons are the boards that make up the sides of the table base and connect the legs.  They are also called table skirts.  Dimensions are 3 1/2" wide and 22 1/4" long across the ends and 62" long down the sides.  For a 34x72 inch table and 4x4 legs, these apron lengths inset the legs roughly 2" on all sides.  The wood is 3/4" to 1" thick rough-cut wood from our old barn.  The red color was a little stark so I sparsely brushed a coat of chalk paint on and waxed again with Briwax.
The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?
*Please NOTE: While my table has held up well and had only a small amount of movement after 2 1/2 years, there are certainly things I would do differently with more experience under my belt. For beginners, I'd recommend using biscuits and glue for the top planks. Dowels or floating tenons/dominos are another option. Do make sure to let the wood properly dry.
Chances are in any woodworking project, you’re going to have to connect two pieces of material. Screws are ideal for this – much better than nails – but there are hundreds of different types and sizes, all for different applications. We will review the most common types and applications so that you can quickly determine what type you will need for your project and how to use it.

In regards to your breadboard ends: You might be able to get away with what you did depending on how dramatic the humidity difference between seasons is in your area, but in the future, you might want to elongate your dowel holes in the tongue of the joint - all but the center hole. Specifically, you want to put a pin in the center of the table end (no hole elongation) and then elongate the holes on either side - maybe 1/16" to each side of center (it's OK to glue the center like you did). This allows the center pin to keep the board centered (duh) and then allows the table top to grow and shrink across it's width without putting undue stress on the breadboard ends. This is important because wood expands/contracts across it's grain significantly more than it does along it's length, so when you have a joint where end grain meets side grain (as in your breadboard ends) NOT taking this into account can mean that your project disassembles itself - or at least becomes "rickety" as the expansion/contraction cycle loosens the joint. The amount of growth you can expect is determined by wood species, initial moisture content of the wood, and humidity change across seasons. There are online references you can check to see how much you would want to elongate those holes.


Learning from the ideas of other woodworkers, while avoiding their mistakes is an excellent way to design and set-up your own shop layout. Setting up a woodworking shop as a hobby place, or for a some one more serious, who even may venture off into some sort of woodworking business; is not as easy as it might sound. Knowing the correct steps to follow will save you time and money, but it will also save you a lot of stress down the road.
Don't believe the mainstream thinking that hand tools are irrelevant, too slow to be useful, or less effective than power tools. Ignore, or at least take with a grain of salt, the power tool devotees who will say "There's a reason they invented power tools, ya know!" Your "shop" is a bench attached to the inside of a coat-closet door in a one-room studio apartment right now. Power tools are going to bother that nice med student next door, and that closet shop doesn't have any ventilation for the amount of dust you'll produce. Hand tools can be more efficient (in speed, quick access, storage, and lack of set up), they're quieter, and the pleasure of silence afforded by quiet hand tools--just a few soft noises produced by your tools--is a pleasure not to be overlooked. They're portable and will move with you, you'll learn more about how different types of wood behave, and, when you run into one of those power tool zealots, just go over to Todd's house and watch a few episodes of The Woodwright's Shop to get your respect for hand tools back in check.
After placing such an amazing wooden house to your lounge’s beauty would be enhanced. Wooden item that I love very much is a beautiful house. You can see one in the image above. You can easily make it at home easily by having some necessary tools. These things are not only beautiful, but they can give an adorable look to your place. Another amazing thing is that they can be built in many shapes and sizes, as and how you need it. It takes some serious woodworking knowledge and skill to build a nice wooden toy house.
You must know you should have a bit of woodwork skills to do this innovative and stimulating work. All you need are a few pieces of wooden boards, wood cutter, electric drill, hammer, screws and plates. You can easily make these wooden cutting boards by joining equal size wooden pieces of square shapes. You can also do easily. The tutorial explains the procedure for building this beautiful wooden board.
Use: White vinegar poured into a glass jar with steel wool that you have pulled apart and loosened. After fifteen minutes, brush onto the wood. After the surface is dry, you can leave it as-is or clear coat it with a product like Minwax One Coat Polyurethane. Distress prior to finishing, if so desired.http://www.wikihow.com/Age-Wood-With-Vinegar-and-Steel-Wool 

Don't believe the mainstream thinking that hand tools are irrelevant, too slow to be useful, or less effective than power tools. Ignore, or at least take with a grain of salt, the power tool devotees who will say "There's a reason they invented power tools, ya know!" Your "shop" is a bench attached to the inside of a coat-closet door in a one-room studio apartment right now. Power tools are going to bother that nice med student next door, and that closet shop doesn't have any ventilation for the amount of dust you'll produce. Hand tools can be more efficient (in speed, quick access, storage, and lack of set up), they're quieter, and the pleasure of silence afforded by quiet hand tools--just a few soft noises produced by your tools--is a pleasure not to be overlooked. They're portable and will move with you, you'll learn more about how different types of wood behave, and, when you run into one of those power tool zealots, just go over to Todd's house and watch a few episodes of The Woodwright's Shop to get your respect for hand tools back in check.

Some friends of ours have been wanting a DIY farmhouse table for some time now. After hearing about their shopping trip and the prices they were looking at spending on one I felt obligated to step in and make this one of my next DIY projects. My buddy Jake has no experience with power tools whatsoever, bless his heart. So, you’re in for a special treat with this one as you will get to see Jake build this table from scratch with no power tool experience! With a little guidance from me of course.

It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details on internet. Follow the steps properly to make a nice and strong wall wooden hanging. This wooden piece makes wooden clips to hold decorative items. The tutorial explains the procedure for building this beautiful wall hanging. Make sure to use only high quality items for any woodworking project.
The video above includes a step-by-step tutorial for making a wooden toy house. By following these steps, you can easily make it by yourself. You will also need some basic woodworking items, such as wood, pop sticks, cutter, glue and screws, etc. Even if you do not like this one, you can always browse the internet for more beautiful wooden toy houses ideas. I have also shared a link where you can find some really interesting and beautiful wooden houses ideas for every kind. Just select the one you like the most and start building. 

Hand Sanders are the simplest and cheapest sanding you can do and will likely work well for most small projects. You buy the hand sander which is a plate with a handle (typically ~$5) and then attach pieces of sandpaper to the bottom. The biggest advantage to a hand sander is it’s very cheap. It does take a bit of time, but you can achieve a perfectly acceptable finish with it.

For the legs, we purchased black steel gas pipes which had to be measured and cut to size.  After the steel pipes were cut they had to be manually threaded with a pipe threader.  Gas fittings were used to connect the piping. This step resulted in a few choice bad words, it seems you can actually get them already threaded. But why should we take the easy route, when we can make ourselves crazy instead.
*Please NOTE: While my table has held up well and had only a small amount of movement after 2 1/2 years, there are certainly things I would do differently with more experience under my belt. For beginners, I'd recommend using biscuits and glue for the top planks. Dowels or floating tenons/dominos are another option. Do make sure to let the wood properly dry. 

The article explains step by step process for making this awesome piece of wooden art. It is actually very easy to make one.This tutorial shows the making of wooden box with one of the easiest ways. However, it is a bit difficult to make them, but not so much.I make this wooden box at home easily. You can also make it by using basic tools like wood cutters, hammer, drill and measuring tape. I made it at home for my creativity in easy steps.
Have you heard about the wooden swords for decoration? If no, then I am sharing the picture of the wooden swords with you. This is an ideal gift for giving your loved ones. You can hang these swords on the wall and in the lobby. It looks great and gorgeous. Have a look at the pictures which I am sharing with you, I am sure you would like these pictures. These are the pictures which are best for wall decoration. So, you should choose these swords for giving the gifts to your loved ones.

All of our tables are available in the color and finish of your choice.  Our existing color pallet includes 90 paint colors,  multiple stain color options in each workshop collection and several wax color options for our reclaimed woods.  Please feel free to explore all of our paint and stain options to help guide your design plans.  All of paint and stain finishes include a durable water based clear top coat.  This makes it easier to keep the table top clean with a damp sponge (no chemicals!) and provides protection from water rings. (How to Clean a Wooden Dining Table) 
Hybrid saws are essentially built like the old contractor saws, but with the motor in the cabinet, just like a cabinetmaker saw. They are much cheaper than cabinetmakers saws and not as heavy. The saw at left is my first table saw, a 40-year old contractor saw, which I enclosed on the bottom to keep the sawdust inside. At present, I use a hybrid table saw
This video shows the making of wooden hanging with one of the easiest ways. I make this wooden stylish wooden hanging at home easily and decorate with the variety things that give fabulous look to my room. You can also make it by using basic tools like wood cutters, hammer, drill and measuring tape. I made it at home for my creativity in easy steps. It is actually very easy and interesting to make. Size, shape and design is according to your choice when you made it.
×