Use: White vinegar poured into a glass jar with steel wool that you have pulled apart and loosened. After fifteen minutes, brush onto the wood. After the surface is dry, you can leave it as-is or clear coat it with a product like Minwax One Coat Polyurethane. Distress prior to finishing, if so desired.http://www.wikihow.com/Age-Wood-With-Vinegar-and-Steel-Wool
To make the top, align the three pieces of 2 x 12. Fit them as tightly together as you can. Bore four pocket-screw holes through the bottom faces of the top pieces, then spread glue on each adjoining edge. With the pieces clamped together so that the ends are flush, fasten with 2½-inch pocket screws. Glue will squeeze out of the joint. Wait a few minutes for the glue to get rubbery, then shave it off with a sharp chisel. Keep the top flat as it dries—I like to clamp cauls across both ends to add stability. Cauls are 2 x 4s or other pieces of stout wood turned on their edges.

After we got all our aggression out on the table, I applied a coat of Minwax pre-stain wood conditioner followed by a custom stain I came up with. I’ve purchased several “gray” stains that are supposed to give the wood a weathered, rustic look, but no matter how many coats I add, the gray barely colors the wood at all. I wanted the table to still be light enough to show all the wood grain, but have that old, weathered look to it, and this is the perfect mix I came up with:
Nominal size means the dimension of the lumber “in name only.” In other words, the lumber is called a certain size, even though its true size is smaller. For example, a piece of lumber is called a 4x4 at the store, even though it is only 3 ½” x 3 ½” if you were to measure it with a ruler.http://www.familyhandyman.com/carpentry/making-sense-of-lumber-dimensions/view-all

In my project section I wrote an article about small boxes made with a router. The article was written years ago and the boxes were made several years before that. Thus, I had to use one of those old boxes to write this article as I couldn't exactly remember how I made them. The initial construction process came from that great Canadian TV show, The Router Workshop, but the jig I use was born of necessity. One year I decided to build a pile of these boxes and enter a craft fair. After two or three, I decided there had to be a faster way to set up for the cuts, so I used a discarded table saw sled to fashion the jig in this article.


This snowman kit post is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. The snowflakes are falling softly on the ground. You grab your hat, coat and mittens and head outside to test the snow. … [Read more...]
You can create a simple and affordable eye catching frame for your artwork out of a great old wooden ladder. Simply turning the ladder on its side will allow you to display quite a lot of art in a row for so little money. This simple home decor craft project is an affordable way to introduce color, the vintage look, and even some architectural interest without costing a fortune.
Have you ever heard about a chess which is made of wood? If not, then I am presenting a chess which is the most beneficial and attractive one. I am sharing its picture with you and you can make this chess very easily. The most amazing thing is that you can present it as a gift to other fellows. They would surely admire your gift. I am sharing some pictures of this chess; just have a look at these pictures. I am sure you would like these pictures.

8. Size a tenon on the cap piece to fit the ball’s hole. Undercut its shoulders, too. The cap piece, as shown here, is glued into a shallow hole turned into the face of a waste block. Shape the cap, then part it off the waste block. To clean up the tip, reverse the cap and push the tenon into a new hole in the waste block. Finish the cap on the lathe, then remove it and drill a small, shallow hole for the hanging wire.
Not every woodworking shop have sawhorses, but you'll find them a useful and versatile item to have at hand. A sawhorse can be used as a short-term table, workbench or benchtop stand, and can be use as a workbench extender or to as a temporary lumber self. Build your own sawhorses allows you to customize them to your own needs and wood shop requirements.

Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.


Gain all the knowledge you need to build your own fully accessorized workbench with this step-by-step video featuring George Vondriska. For both beginning and intermediate woodworkers alike, a well-made and intricately customized workbench is a critical tool to ensure efficiency in all your future woodworking projects. Through George’s detailed instruction, you’ll quickly and easily learn
If you want to get into woodworking, a good project to tackle is building your own workbench. It's really not that hard. So if building your own workbench is a bit too much work, or too intimidating, then take a step back and examine whether you really want to get into woodworking. This may be different if your goal is to cut silhouettes of kittens out of plywood with a scrollsaw, but I wouldn't call that sort of activity "woodworking".
If you are searching a very stylish gift for your friends who are females, then your search ends here, as I am sharing a leaf shape jewelry box that is the most stylish one. I am sure your friends would love to have it. They can keep their jewelry in this box. You would not need any other box for keeping your essential items. If you would give it as a gift, your friends would surely love to have it. I am sharing some of the pictures of this jewelry box, just have a look at these pictures. 

Jigsaws have a reciprocating blade, and are a great do-it-all saw which we use them quite often on our projects. They excel at making oddly shaped cuts and curves, but aren’t so great if you need perfectly straight cuts. Another advantage to jigsaws is that the blades are small, cheap, and interchangeable so that you can quickly swap between cutting different materials.

In regards to flattening the top, another technique would be take a pencil (soft lead) and lightly draw some big lazy squiggles across the top - enough so that there is a line every few inches. Then, use either a jointer plane or a belt sander to flatten the top until the squiggles are gone. The lines give you a reference to what is high and what is low - and when you are finished in a particular area. With the jointer plane, you want to stroke at about 45 degrees to the grain of the wood, and with a belt sander, you want to keep the sander flat on it's platen (don't let it tilt and dig in) and use wide, arcing, sideways sweeps with very light pressure - again at about 45 degrees to the grain of the wood - never let the sander start or stop when in contact with the surface. In both cases, finish with light sanding with either a belt sander, linear sander, or by hand, stroking in the direction of the grain. Palm sanders can leave swirls.

Nothing could be easier to accomplish than these rustic, personalized wood slice tree ornaments. After slicing a log into discs, screw in an eye hook, and thread with some jute twine for a hanger. Decorate with paint or metallic markers, or try the clever ink-jet-printer transfer technique that Upcycled Treasures used for the ornaments shown here. One log will make gifts for your entire extended family.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Just look at this small and cute helicopter that is made of wood. I am sure you would enjoy having it. Your kids would play with this. If you are giving gifts to your friend on the birthday of his/her child, then it is the best gift. I am sure your friend would admire this gift and their kids would just love having it. There are different colors of this helicopter. I am sharing some of the pictures of this helicopter. Have a look at these pictures and get an idea about it.
In my project section I wrote an article about small boxes made with a router. The article was written years ago and the boxes were made several years before that. Thus, I had to use one of those old boxes to write this article as I couldn't exactly remember how I made them. The initial construction process came from that great Canadian TV show, The Router Workshop, but the jig I use was born of necessity. One year I decided to build a pile of these boxes and enter a craft fair. After two or three, I decided there had to be a faster way to set up for the cuts, so I used a discarded table saw sled to fashion the jig in this article.
Never consider using wood from a high volume store such as Lowes or Home Depot for furniture. You will almost assuredly have serious warpage as this wood is never dried to the proper level prior to being placed in the stores for sale. I normally shoot for 7%-8% moisture content. Anything greater than that will have a tendency to warp as it continues to dry out. You need to go to a lumber yard where the boards are actually dried prior to sale. You can acquire an inexpensive meter and check the boards yourself prior to purchase. Actually, I prefer air dried lumber as opposed to kiln dried. I have let it dry for 1-2 years or more prior to using it. I don't run it through the planer until I am ready to use it. Hope this is helpful. By the way, Red Oak or Cherry makes beautiful furniture. I seldom use white oak because the stuff is really tough to work with due to its hardness. Make beautiful furniture, though!
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
The article explains step by step process for making this awesome piece of wooden art. It is actually very easy to make one.This tutorial shows the making of wooden box with one of the easiest ways. However, it is a bit difficult to make them, but not so much.I make this wooden box at home easily. You can also make it by using basic tools like wood cutters, hammer, drill and measuring tape. I made it at home for my creativity in easy steps.
If you're dreaming of a white Christmas, prep your home with this practical and pleasing boot rack. Blogger Stephanie Lynn constructed this fixture from stock lumber and 2-inch dowels to keep the slush and mud outside the house, where they belong. Glue down the dowels, or leave them dry-fitted so you can disassemble and store the rack easily during the summer months.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
This Welcome Farmhouse Sign post is sponsored by The Home Depot. I have been compensated for my time and provided with product. All ideas and opinions are my own. This post contains some affiliate links for your convenience. Click here to read my full disclosure policy. Farmhouse style wood signs are a fun way to personalize your space. They are fairly easy to make yourself … [Read more...]
We’ve already done rope, and now we’re on to another rustic material we love: wood! It’s as basic of a material as clay and is constantly reinvented by DIYers, crafters, artists, hackers, and carpenters. To get inspired to create our own batch of cool wooden objects, we turned to our favorite fellow makers to see what projects they’ve come up with. Scroll down for our top DIY wood project picks.
This is another basic farmhouse table design which you can easily build. However, the table is large with a seating capacity of at least ten people. This table is also a great addition to be in your home as it serves many purposes including storage apart from dining. The instructions are provided in two separate parts; first part includes the construction process and the second part includes the finishing touches.

If your space is very limited in your living or kitchen, you will love this farmhouse table design which can also be used as a kitchen island. This feature makes it perfect for keeping it in the kitchen space. If you have some woodworking skills, consider making pocket holes without adding 2×2 supports as in the original plan which saves both money and time. In this process, you will not have to drill or cut more holes, and all the screw holes can be hidden providing a better finish.
This activity shows the making of square shape wooden cutting board with one of the easiest ways by using basic tools. I made it at home for my inspiration behind easy steps. This tutorial is easy enough for even beginners to understand and follow. So I am not going to explain each and every step. You can also make by painting the wood pieces, cutting, assembling, and joining in a square order to make it and put it in every corner of your kitchen to give classy look.
A track saw will allow you to make many cuts that would otherwise require a table saw, and is hard to beat if you need to cut up whole sheets of plywood. But for the price of a track saw, you can buy a table saw, and table saws are so much more versatile and convenient. So if you are just starting out, don't let anybody tell you that you don't need a table saw if you have a track saw. Save the track saw purchase for later.
You can also make wonderful variety of wooden boxes easily at home. It is actually very stress-free and interesting to make. You must know you should have a bit of woodwork skills to do this innovative and stimulating work. All you need are a few pieces of wooden boards, wood cutter, electric drill, hammer, screws and plates. You can easily make these wooden boxes by joining equal size wooden pieces of square shapes. You can also do easily.

Chances are in any woodworking project, you’re going to have to connect two pieces of material. Screws are ideal for this – much better than nails – but there are hundreds of different types and sizes, all for different applications. We will review the most common types and applications so that you can quickly determine what type you will need for your project and how to use it.

Nearly every woodworking project in one form or another will require you to check some intersection, joint, or board end for squareness, or "square." In some cases, you'll need to confirm that an entire assembly is square. For small projects, you can use a squaring tool, such as a try square, speed square, or framing square. For larger projects, you can check for square by measuring diagonally between opposing corners: The assembly is square when the measurements are equal. You can also use the 3-4-5 method, based on the Pythagorean Theorem: a2 + b2 = c2.

Our existing color pallet includes 90 paint colors,  multiple stain color options and several wax color options.   Need a custom color?  We can do that too!    The possibilities are endless!   Check out our Farmhouse Tables FAQ guide and all of our dining table choices listed below for more information.  Want some advice?  Contact one of our table consultants.
Wow, this is really big rolling dice and the special thing of this dice is that it is made from wood. I think wooden dice are durable dice. This is one of the best decorations I have ever found. The main question is that why it is so special for me? Basically, I am a game lover and I have made this wooden dice for the decoration of home. The size of this dice is large instead of normal games dice. This is really special project for me that am the reason I make it with full charm. You can see the full image of beautiful dice in the following link.
This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.
Another way to customize the look of your table is with the top shape.  In addition to traditional rectangular and round table tops, we also offer oval and racetrack tops.  What’s that?  A racetrack table top has curved ends and straight sides whereas an oval top is curved on all sides.  As with table bases, it is important to consider form with functionality!  In addition to shape and size, all of our table tops come in standard (about 1″), thick (about 1.5- 1.75″) and extra thick (+2″) thicknesses.  Do you need an extra large table, a very narrow table or an odd shape?  All of table lengths, widths and shapes are customizable.  Just ask us if you don’t see the exact size you are looking for!
Drawing inspiration from a round trestle table that was worth $3350, Rogue Engineer came up with their free DIY plan to make the table cheaper. Unexpectedly, you can make this excellent table for around $40. You may think that round tables are difficult to build, but if you have the proper tools and follow the instructions carefully as provided, you can actually make this table with ease.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
As Chief Creative Officer and Founding Partner at Brit + Co, Anjelika Temple brings her voracious consumption of all things creative and colorful to DIY projects, geeky gadgetry finds and more. When she's not DIY-ing her heart out, you'll find her throwing dinner parties with friends or adventuring with her husband David, their daughter Anokhi, and their silly dog Turkey.

A good friend celebrated a milestone birthday this year, and since he’s a real wine afficionado, I wanted to give him a few very nice bottles of wine presented in a special way. I’ve seen expensive vintage wines sold in wooden presentation boxes, but I wanted to make something that’s well beyond the ordinary. So I designed a box that presents the wine bottles by “popping them up” as the lid is opened.
×