In regards to flattening the top, another technique would be take a pencil (soft lead) and lightly draw some big lazy squiggles across the top - enough so that there is a line every few inches. Then, use either a jointer plane or a belt sander to flatten the top until the squiggles are gone. The lines give you a reference to what is high and what is low - and when you are finished in a particular area. With the jointer plane, you want to stroke at about 45 degrees to the grain of the wood, and with a belt sander, you want to keep the sander flat on it's platen (don't let it tilt and dig in) and use wide, arcing, sideways sweeps with very light pressure - again at about 45 degrees to the grain of the wood - never let the sander start or stop when in contact with the surface. In both cases, finish with light sanding with either a belt sander, linear sander, or by hand, stroking in the direction of the grain. Palm sanders can leave swirls.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.
East Coast Creative provides this DIY plan to make your farmhouse table which can be used for a picnic with many guests. This gigantic table can fit 12-14 people. Though it does not have benches, the top of the table spreads out like a traditional picnic table. You can add chairs of your choice and so, if you want to add a modern twist, simply choose chairs with modern styles.
How amazing to have the earrings which are very elegant looking. I just came across these earrings online with wood and you can see the designs inside it. If you wear these earrings on the parties, your personality would become attractive. Now, don’t buy expensive earrings for parties.Have a look at the image and you would find it great to make them.
To start, make a base assembly out of the aprons, legs, and stretchers. Attach one leg on either side of one of the short aprons. Bore two holes for pocket screws into each side of the apron's back, four in total (fig. 1). Clamp the legs to the apron, but add a ⅛-inch piece of wood to the front as a spacer (fig. 2). This will offset the face of the apron from the face of the leg, pushing it back a bit and creating a nice dimensionality. Drive the pocket screws through the apron into the leg. Repeat the same procedure for the second leg–apron assembly.

Scrollsaws are good for projects like cutting puzzles or silhouettes of cutesey animals out of wood. But for making furniture, scrollsaws just aren't up to the task. Scrollsaws, along with Dremel tools, do have their uses in crafts, but for woodworking, they are just a little too small. That said, Dremel tools are very useful for sharpening brad point drill bits, forstner bits, and bandsaw blades, so they do have a use in woodworking.
Just check out this enticing and legant mirror that portray woodworking art finely blended with creativity. You can have it on the wall, especially in the lobby it looks great. It enhances the looks of your dinning room and your drawing room. I just found this over the interent and people are highly admired by this design. So, lets have a look at its image, you will get guidance on making it.
Have you ever heard about a chess which is made of wood? If not, then I am presenting a chess which is the most beneficial and attractive one. I am sharing its picture with you and you can make this chess very easily. The most amazing thing is that you can present it as a gift to other fellows. They would surely admire your gift. I am sharing some pictures of this chess; just have a look at these pictures. I am sure you would like these pictures.

In this month’s woodworking project demonstration, George Vondriska teaches you the step-by-step process for building a coat tree that will look great in your home or workshop. He demonstrates the simple techniques for installing wrought-iron hooks, crafting the coat tree’s feet, and quarter sawing to achieve that beautiful face grain on all four sides.


Douglas fir from home improvement centers will almost always warp when you try to make a flat top. It is never dried to the same extent as hardwood and ships out for the purpose of being used as framing lumber, not furniture lumber. That said, you can do it, but buy it and let it sit in your garage for a few months or longer to let it further dry and acclimate to your environment. Even better if you plane it down after that waiting period, then allowing it to acclimate for another week or so to make it works out all of its twists prior to being turned into a top. Do you have any hardwood dealers in your area? Try visiting one and make an investment in your table...buy some good maple (soft maple is worlds harder than new douglas fir - you don't need hard maple, ie:or sugar/rock maple).


Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
Not at all! I meant to put the total cost in the post, so thank you for reminding me! The wood totaled around $50 for the table and $34 for both benches. We spent another $25 or so on screws and miscellaneous tools, so for about $110, I’d say that’s not too bad!! It took my husband and I a couple hours to build the table, another couple hours to build the benches, and about 2 days to sand, distress, stain, and seal everything.

Build your own furniture, a dream of many but a reality for few. In this video I show you how I make farm tables. This is one made for a customer for a new house. It's 10 feet long and made from red oak, sawn from a dead standing tree. The base is made from spruce and yellow pine. It is constructed with mortise and tenon joints, using a hollow chisel mortiser and a tenon jig I made for the table saw. 

​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.
Living in South Florida gives me the ability to work under the bright Florida sun by simply rolling the woodworking power tools out from under the roof. On days like the one when this photo was taken, when rain is expected later in the afternoon, most of the tools can be kept under the roof, and rolled away into large lockable storage rooms in less than five minutes. 

This basic table from Instructables is also very easy to build, and also the benches are simple in design. If you are looking to make a simple table with many seating, you can consider making this table. However, the chairs would require some good carpentry skills or you can buy them separately. It is recommended to use kiln dried lumber which can be readily available at your home store. Check for the initials KD or HT to know the type of lumber to be used.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.

Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many

To start, you'll want to cut out the pieces. Crosscut the top pieces, breadboard ends, stretchers, and legs. Note that the breadboard ends are slightly wider than the tabletop. This is a rustic detail with a practical aspect. It will allow the top to expand and contract with humidity and never be wider than the breadboard ends. There is also a slight overhang on the stretchers, for a similar reason. When you cut the legs, double-check that the length is a good fit for your dining-room chairs, especially if any of them have arms. Chairs with arms should be able to easily slide under the table's aprons.
×